The lock stores up to 6 User Codes-4 to 10 digits. You should delete the preset code (see how to delete a User Code below) and then add your personal User Codes. The lock comes with a preset User Code-1234. How to Add User Codes on a Garrison Electronic DeadboltĪ User Code for this lock is a 4 to 10-digit code that allows you to unlock the lock via the keypad. You may also read our article about programming Emtek and Brinks electronic locks. Note: There’s no limit to how many times you can change the Programming Code-you can change it as many times as you want. But note that the preset code won’t be active if it was previously changed, so you need to enter your current Programming Code during the process. If you previously changed your Programming Code and want to change it again for any reason, the process is the same as changing the preset code. Now your new Programming Code is set and it should be used for all programming. Step 3: Enter your new Programming Code (4 to 10 digits) and then press the Garrison button.Step 2: Press 4 and then press the Garrison button.(If you’ve never changed the Programming Code, your current Programming Code is the preset code-0000). Step 1: Enter your current Programming Code and then press the Garrison button.Here’s how to change the Programming Code on a Garrison Electronic Deadbolt: To ensure security, it’s recommended that you change the preset Programming Code to a unique personal code-4 to 10 digits. For example, you’ll need to first enter your Programming Code before adding or deleting a User Code. As you probably know, the Programming Code allows you to make changes to your lock settings. This lock comes with a preset Programming Code-0000. Changing the Programming Code on a Garrison Electronic Deadbolt Let’s head over to other programming instructions. That’s all about performing the door handing detection, and the lock can now function electronically. Press 0 and then press the Garrison button.Enter the default Programming Code (0000) and then press the Garrison button.So, here’s how to perform the Door Handing Detection on your Garrison Electronic Deadbolt: You also need to run the Door Handing Detection after factory resetting your lock. Note that your lock won’t work electronically if you don’t perform the Door Handing Detection. Why can’t I change the default Programming Code nor add new User Codes?Īfter installing your Garrison Electronic lock (first-time installation), the first thing you need to do is perform the Door Handing Detection.The lock beeps three times when I press the Programming button and won’t lock-what to do?.Why is my lock not responding when buttons are pressed?.Garrison Electronic Deadbolt Common Problems and Troubleshooting Tips.Factory Resetting a Garrison Electronic Deadbolt.How to Lock/Unlock a Garrison Electronic Deadbolt.Enabling/Disabling Auto-Lock on a Garrison Electronic Deadbolt.How to Delete User Codes on a Garrison Electronic Deadbolt.How to Add User Codes on a Garrison Electronic Deadbolt.Changing the Programming Code on a Garrison Electronic Deadbolt.If the lock tests properly, re-install the strike plate and test the lock one more time to make sure the bolt is not snagging on the door frame.Test the deadbolt latch again, if necessary.
If not, use the drill to make the hole another 1/4 inch deeper. If the twist knob stops in the same position with the door opened and closed, the hole is deep enough. Using the appropriate-sized spade bit and an electric drill, cut the hole in the door frame about 1/4 inch deeper.Safety is the most important thing to keep in mind when using tools. This could easily injure you or damage the door frame. If you don’t remove the strike plate, the opening will not be wide enough for the spade bit and it could snag, causing the drill to buck. Do not try to deepen the hole without removing the plate. Remove the strike plate from the door frame.If the twist knob stops short when the door is closed, the hole in the door frame has not been drilled deep enough, which could make it easier for a criminal to defeat the lock.If the twist knob lever stops in the same position for both tests, the strike plate and hole are most likely installed properly. Test the deadbolt by turning the twist knob to latch and unlatch the lock with the door open and then again with the door closed.Steps To Inspect and Repair an Improperly Installed Deadbolt Lock We show you one common problem with deadbolt lock installations that’s easy to identify and easy to fix. if it isn’t fully extended, it’s possible to unlock the door without a key. A deadbolt lock is only secure when the bolt is fully extended into the door frame. A deadbolt lock only keeps the bad guys out if it’s installed properly.